Second, the performance indicators of the speaker system
1) Frequency response (effective frequency range)
This indicator reflects the main frequency range in which the speaker works.
When a constant voltage source is applied to the speaker and the source frequency is changed from low frequency to high frequency, the sound pressure generated by the speaker will vary with frequency. The resulting sound pressure-frequency curve is the frequency response curve of the loudspeaker. The IEC (International Electrotechnical Commission) stipulates that the frequency limit of the sound that can be reproduced by the speaker, that is, the effective frequency range, is the frequency range in which the average sound pressure level of one octave near the peak is reduced by 10 dB in the sound pressure frequency characteristic curve of the speaker. The wider the range, the better the sound reproduction characteristics
Generally, the minimum required frequency response of the high-fidelity speaker box is 50-12500HZ (+4~-8dB), and it is enough to reach 50-16000Hz. Of course, 30-20000Hz is better.
2) Rated impedance
It refers to the impedance value measured at the input of the loudspeaker at a particular operating frequency (intermediate frequency). Usually indicated on the product nameplate, given by the manufacturer. The impedance characteristics of the speaker. The rated impedance given by the manufacturer is usually the impedance modulus at which the maximum work is expected in the rated frequency range. The rated impedance is generally specified as 4 ohms, 8 ohms, 16 ohms, 32 ohms, etc., and 3 ohms and 6 ohms are also used abroad.
3) Power
The power level of the speaker is one of the important indicators for choosing to use the speaker. It should be pointed out that the standard method of the domestic and foreign speakers is very different, because the definition of the power is different. The nominal power of a typical loudspeaker is rated power.
Rated power or rated noise power is the input power when the speaker can work continuously for a long time without generating abnormal noise. In general, the pink noise signal is used for testing, and the specific filter is used to test within the rated frequency range. According to the IEC standard, the loudspeaker to be tested should ensure that no abnormalities occur during 100 hours of continuous operation. Incidentally, the US EIA standard stipulates that the test time is 8 hours and the filters are different.
The maximum noise power is different from the rated power. It is the ability to indicate that the speaker is subjected to a large input power for a short period of time. The test time is only a few seconds or a few minutes. Generally, the maximum noise power is 2-4 times the rated power.
4) Sensitivity
The characteristic sensitivity is the sound pressure level measured at 1 m in the axial direction when the speaker is applied with a pink noise signal voltage equivalent to 1 W of the rated impedance. The sensitivity and efficiency of the speaker box are two different concepts. The efficiency is the ratio of the output sound power to the input power, but in general the speaker box with high sensitivity is also more efficient. Second, the performance indicators of the speaker system
1) Frequency response (effective frequency range)
This indicator reflects the main frequency range in which the speaker works.
When a constant voltage source is applied to the speaker and the source frequency is changed from low frequency to high frequency, the sound pressure generated by the speaker will vary with frequency. The resulting sound pressure-frequency curve is the frequency response curve of the loudspeaker. The IEC (International Electrotechnical Commission) stipulates that the frequency limit of the sound that can be reproduced by the speaker, that is, the effective frequency range, is the frequency range in which the average sound pressure level of one octave near the peak is reduced by 10 dB in the sound pressure frequency characteristic curve of the speaker. The wider the range, the better the sound reproduction characteristics
Generally, the minimum required frequency response of the high-fidelity speaker box is 50-12500HZ (+4~-8dB), and it is enough to reach 50-16000Hz. Of course, 30-20000Hz is better.
2) Rated impedance
It refers to the impedance value measured at the input of the loudspeaker at a particular operating frequency (intermediate frequency). Usually indicated on the product nameplate, given by the manufacturer. The impedance characteristics of the speaker. The rated impedance given by the manufacturer is usually the impedance modulus at which the maximum work is expected in the rated frequency range. The rated impedance is generally specified as 4 ohms, 8 ohms, 16 ohms, 32 ohms, etc., and 3 ohms and 6 ohms are also used abroad.
3) Power
The power level of the speaker is one of the important indicators for choosing to use the speaker. It should be pointed out that the standard method of the domestic and foreign speakers is very different, because the definition of the power is different. The nominal power of a typical loudspeaker is rated power.
Rated power or rated noise power is the input power when the speaker can work continuously for a long time without generating abnormal noise. In general, the pink noise signal is used for testing, and the specific filter is used to test within the rated frequency range. According to the IEC standard, the loudspeaker to be tested should ensure that no abnormalities occur during 100 hours of continuous operation. Incidentally, the US EIA standard stipulates that the test time is 8 hours and the filters are different.
The maximum noise power is different from the rated power. It is the ability to indicate that the speaker is subjected to a large input power for a short period of time. The test time is only a few seconds or a few minutes. Generally, the maximum noise power is 2-4 times the rated power.
4) Sensitivity
The characteristic sensitivity is the sound pressure level measured at 1 m in the axial direction when the speaker is applied with a pink noise signal voltage equivalent to 1 W of the rated impedance. The sensitivity and efficiency of the speaker box are two different concepts. The efficiency is the ratio of the output sound power to the input power, but in general the speaker box with high sensitivity is also more efficient. Second, the performance indicators of the speaker system
1) Frequency response (effective frequency range)
This indicator reflects the main frequency range in which the speaker works.
When a constant voltage source is applied to the speaker and the source frequency is changed from low frequency to high frequency, the sound pressure generated by the speaker will vary with frequency. The resulting sound pressure-frequency curve is the frequency response curve of the loudspeaker. The IEC (International Electrotechnical Commission) stipulates that the frequency limit of the sound that can be reproduced by the speaker, that is, the effective frequency range, is the frequency range in which the average sound pressure level of one octave near the peak is reduced by 10 dB in the sound pressure frequency characteristic curve of the speaker. The wider the range, the better the sound reproduction characteristics
Generally, the minimum required frequency response of the high-fidelity speaker box is 50-12500HZ (+4~-8dB), and it is enough to reach 50-16000Hz. Of course, 30-20000Hz is better.
2) Rated impedance
It refers to the impedance value measured at the input of the loudspeaker at a particular operating frequency (intermediate frequency). Usually indicated on the product nameplate, given by the manufacturer. The impedance characteristics of the speaker. The rated impedance given by the manufacturer is usually the impedance modulus at which the maximum work is expected in the rated frequency range. The rated impedance is generally specified as 4 ohms, 8 ohms, 16 ohms, 32 ohms, etc., and 3 ohms and 6 ohms are also used abroad.
3) Power
The power level of the speaker is one of the important indicators for choosing to use the speaker. It should be pointed out that the standard method of the domestic and foreign speakers is very different, because the definition of the power is different. The nominal power of a typical loudspeaker is rated power.
Rated power or rated noise power is the input power when the speaker can work continuously for a long time without generating abnormal noise. In general, the pink noise signal is used for testing, and the specific filter is used to test within the rated frequency range. According to the IEC standard, the loudspeaker to be tested should ensure that no abnormalities occur during 100 hours of continuous operation. Incidentally, the US EIA standard stipulates that the test time is 8 hours and the filters are different.
The maximum noise power is different from the rated power. It is the ability to indicate that the speaker is subjected to a large input power for a short period of time. The test time is only a few seconds or a few minutes. Generally, the maximum noise power is 2-4 times the rated power.
4) Sensitivity
The characteristic sensitivity is the sound pressure level measured at 1 m in the axial direction when the speaker is applied with a pink noise signal voltage equivalent to 1 W of the rated impedance. The sensitivity and efficiency of the speaker box are two different concepts. The efficiency is the ratio of the output sound power to the input power, but in general the speaker box with high sensitivity is also more efficient.
Beam Light
1).Excellent pattern,mute,the best effect of the light is 5 to 30 meters.
2).Competitive price and high quality.
3).LCD Chinese and English bilingual menu,brightness.
4).Suitable for performances,bars,banquet hall,multi-purpose conference room,theater,studio,etc.
Our company have 13 years experience of LED Display and Stage Lights , our company mainly produce Indoor Rental LED Display, Outdoor Rental LED Display, Transparent LED Display,Indoor Fixed Indoor LED Display, Outdoor Fixed LED Display, Poster LED Display , Dance LED Display ... In additional, we also produce stage lights, such as beam lights Series, moving head lights Series, LED Par Light Series and son on...
Beam Light Series,Sharpy Beam Light,Led Moving Beam Head Light,Led Beam Light
Guangzhou Chengwen Photoelectric Technology co.,ltd , https://www.cwstagelight.com